For medical device design engineers

Battery selection guide

Choosing a cell early saves a housing redesign later. This guide compares the chemistries Tianqiu makes and lists the questions to settle before you pick a size.

Chemistries compared

Typical characteristics of each chemistry. Confirm values for a specific cell against its Tianqiu datasheet.

ChemistryNominal voltageDischarge profileTypical end voltagePulse capabilityKey design constraintTypical devices
Zinc-air button1.45 VFlat≈1.1 VModerate; limited by air diffusionNeeds an air path; activated by removing the tabHearing aids, sound processors
Lithium coin (Li-MnO₂)3.0 VFlat≈2.0 VLow to moderate; voltage dips under pulsesInternal resistance under radio bursts and coldGlucose meters, wearable patches, sensors
Alkaline button1.5 VSloping≈1.0–1.2 VLowDevice must tolerate falling voltageThermometers, small instruments
Alkaline AA / AAA1.5 VSloping≈0.9–1.0 VModerate; capacity falls at high drainDevice must tolerate falling voltageBlood pressure monitors, pulse oximeters
Lithium cylindrical (Li-MnO₂)3 V / 6 VFlat≈2.0 V per cellHighPrimary only; protect against chargingHigh-pulse portable devices
Illustrative discharge shapes: flat chemistries hold near nominal voltage until late in life, sloping chemistries fall steadily 100%80%60% 0%50%100% Capacity delivered Voltage, % of nominal Flat: zinc-air, lithium Sloping: alkaline
Illustrative shapes only, not Tianqiu test data. A flat profile lets you set a tight brown-out threshold; a sloping profile needs circuitry that runs down to the end voltage.

Sizes at a glance

The most-specified zinc-air and lithium coin cells, drawn to the same scale.

Zinc-air hearing aid cells and lithium coin cells drawn at the same scale, from the 5.8 mm A10 to the 20 mm CR2025A105.8 × 3.6 mmA3127.9 × 3.6 mmA137.9 × 5.4 mmA67511.6 × 5.4 mmCR9279.5 × 2.7 mmCR102510.0 × 2.5 mmCR162016.0 × 2.0 mmCR202520.0 × 2.5 mm10 mm
Colored dots show the standard hearing aid tab colors.

Questions to settle before choosing a cell

  1. Voltage window. What is the lowest voltage your circuit runs at, and does a regulator or boost converter sit in front of it?
  2. Load profile. Average current, peak pulse current, pulse width and duty cycle. Radio bursts are where most coin-cell designs run short.
  3. Runtime and replacement. How long must the device run between changes, and who changes the cell: a clinician, a patient or nobody?
  4. Environment. Operating and storage temperature, humidity, and whether the housing is sealed.
  5. Space. The diameter and height envelope, and how the cell connects: holder, spring contacts or solder tabs.
  6. Shipping and storage. How long cells sit before use, and whether lithium shipping rules apply to the finished device.
  7. Compliance. Which declarations and test reports your design history file and regulatory submission will need.

Same size, different chemistry

Some zinc-air and alkaline cells share dimensions. If your device is meant for one chemistry, mark the compartment and the instructions so the wrong cell isn't fitted.

DimensionsZinc-airAlkaline
7.9 × 3.6 mmA312 (PR41), 1.45 VAG3 (LR41), 1.5 V
11.6 × 5.4 mmA675 (PR44), 1.45 VAG13 (LR44), 1.5 V

Documentation for your design file

Tianqiu can supply the following on request:

  • Cell datasheets and discharge curves
  • UL 1642 recognition for lithium cells
  • ISO 14971 risk management information
  • RoHS and REACH declarations
  • Conflict-minerals reporting
  • UN 38.3 test information for lithium cells
  • Documentation to support your IEC 60601-1 device compliance
  • Lot traceability records and formal change notifications